Orbimon Edge is a small appliance you run on your LAN next to your Starlink router. It reads the dish over the local network and sends metrics to Orbimon over HTTPS. The image is generic: you link it to your site with the monitor token from the app.
Supported hardware is summarized on the Orbimon Edge product page. Raspberry Pi 3 Model B+, Raspberry Pi 4, Raspberry Pi 5, and Orange Pi Zero 3 are tested and working with the same production image.
Download the image (signed in)
- Sign in to the Orbimon app.
- Open Add monitor (or continue an in-progress monitor) and go to the Install Edge step.
- Select Download Orbimon Edge image.
The download is a zip file named like image_YYYY-MM-DD-orbimon.zip. Today that is image_2026-10-14-orbimon.zip from private dzing release v0.0.5 (about 623 MB). It ships 64-bit Raspberry Pi OS Bookworm (pi-gen arm64) with Edge application 0.0.5 baked in at flash time. The app calls GET /api/v1/edge/image, which redirects to a short-lived link. The same image works for every monitor; you paste the monitor token during setup.
Newer image builds (v0.0.9 through v0.0.11) failed in automation. A new image from main is in progress. No newer zip is published yet.
You can also use a user or service API token with the same endpoint. See Edge API.
Flash the SD card
- Install Raspberry Pi Imager on your computer.
- Choose Use custom and select the
image_YYYY-MM-DD-orbimon.zipfile you downloaded. You do not need to unzip it. - Write to the microSD card.
- Eject the card, insert it in the board, and connect power.
Do not use the legacy install.sh installer. Orbimon ships a ready-to-boot image only.
First boot setup
Allow about one to two minutes after power-on for the Edge to start its setup access point.
- On your phone or laptop, join the open Wi-Fi network named
Orbimon-Setup-XXXX(the four characters are unique to your Edge). - Open http://10.42.0.1/setup in a browser.
- In the setup wizard, complete Network (Ethernet or Wi-Fi on the network that reaches your Starlink router).
- Open Orbimon link and paste the monitor token (
omb_mon_…) you saved from the app. - Finish with Done and wait for the Edge to report online.
In the app, your monitor should show online and receive its first reading shortly after.
Local dashboard
After setup, open http://orbimon-edge.local in a browser on the same network to view the local Edge dashboard and settings. If mDNS does not resolve, use http://<edge-ip>:8080 instead (find the IP from your router DHCP list).
Software updates (manual)
Edge software updates are manual. On the Edge, open Settings, then Updates, choose Check for updates, and when a release is available select Install update. Orbimon does not install Edge updates without your action on the Edge.
The current Edge application release is 0.0.13 (2026-10-27). Boards flashed with today’s v0.0.5 image still run 0.0.5 until you update on the device.
The 0.0.5 updater calls the public GitHub latest-release API without credentials and gets 404, so a freshly flashed board may not see or install 0.0.13 over the air. Do not assume a new board will update itself to the current app. Plan on manual update steps or a newer image once we publish one.
Offline buffering
If the Edge loses internet, it keeps collecting readings locally and uploads them when the link returns. Orbimon Edge holds about 7 days of compressed data on the SD card before the oldest buffered points are dropped.
Factory reset
In the Edge Settings, use Factory reset to clear saved Wi-Fi and return to first-boot setup. After reset, the Orbimon-Setup-XXXX network appears again and you can open http://10.42.0.1/setup. Paste the monitor token again in Orbimon link.
See also
- Orbimon Edge product page (hardware, image, and update notes)
- Getting started
- Troubleshooting
- Edge API